Jeep Wrangler TJ

(1997-2006)

Customize your Jeep Wrangler TJ with M.O.R.E. aftermarket parts and hit the trails with bravado. Whether you're reinforcing your TJ with our mounts and braces, installing our "Rock Proof" front or rear bumpers, or simply adding a dead pedal for comfort, know our parts carry a Lifetime Warranty.

Showing 1–12 of 28 results

Yoke Adaptor (1310 series U-joint) for Ford 8.8 axle

M.O.R.E. stocks the special yoke needed to adapt the Ford 8.8 rear axle pinion flange with a 3 inch center to center bolt pattern to the stock Jeep XJ, YJ, or TJ (1310 series) U-joint. This bolts on the Ford flange and allows you to install your XJ,...

Leaf Spring Mounts for 3-1/4" Axle Diameter

Fits 3-1/4" axle diameter. These weld on spring mounts are 2.5" wide, 7" long (anti-wrap design). They have three holes cut on 1" centers for adjustability of the leaf spring so you can place the axle where you want to. Manufactured in Colorado, laser cut and CNC formed...

Tube Clamp for 1-3/4" Round Tube

This tube clamp will mount to any 1-3/4" OD round tube to mount fire extinguisher, CB radios, lights, or just about anything you can think. Bare steel.

Rod End: 3/4" -16 Left Hand Thread with 5/8" Hole in Ball (Heim Joint)

Want to build your own tie rods, trac bars, radius arms, or link bars, or whatever and need the rod ends (known as Heim Joints) to perform the task? These are super high quality, 52100 bearing steel ball, Teflon® / Kevlar® self-lubricating race, and have a alloy steel...

Sway Bar Brackets from Ford 8.8 Kit for Jeep Wrangler TJ (1997-06) LJ (2004-06)

This sway bar bracket fits all 3-1/4" diameter axles and is 3/16" thick plate, laser cut, and CNC formed. This is the same bracket out of our Ford 8.8 install kit for those of you who want to make your own axle design. Sold in pairs. Fits 1997-06...

Tube Clamp for 2" Round Tube

This tube clamp will mount to any 2" OD round tube to mount fire extinguisher, CB radios, lights, or just about anything you can think. Bare steel.

5/8 Rod End Spacer

Spacers provide room between the heim joint and mounting surface to allow the heim its full range of travel. Required in most heim joint applications, spacers prevent heim joint from binding against mount surfaces and damaging the components. Spacers can also be used to adjust the clearance between...

Tube Clamp for 2-1/4" Round Tube

This tube clamp will mount to any 2-1/4" OD round tube to mount fire extinguisher, CB radios, lights, or just about anything you can think. Bare steel.

Tube Clamp for 1-1/2" Round Tube

This tube clamp will mount to any 1-1/2" OD round tube to mount fire extinguisher, CB radios, lights, or just about anything you can think. Bare steel.

Tube Clamp for 1" Round Tube

This tube clamp will mount to any 1" OD round tube to mount fire extinguisher, CB radios, lights, or just about anything you can think. Bare steel.

Coil Retainer from Ford 8.8 Kit for Jeep Wrangler TJ (1997-2006) LJ (2004-06)

This coil retainer (used with 98700-3 Coil Bucket) is 3/16" thick plate, laser cut, and CNC formed. This is the same bracket out of our Ford 8.8 install kit for those of you who want to make your own axle design. Sold each. Fits 1997-06 Jeep Wrangler TJ...